A Step-by-Step Overview to Installing a Bath Tub
A Step-by-Step Overview to Installing a Bath Tub
Blog Article
Listed here in the next paragraph yow will discover some really good information and facts relating to Installing A Bathtub.
Installing a bath tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a new one is also a reasonably hard job. If the old tub is conveniently obtainable, the job can move speedily; if you need to open up a wall surface to eliminate the old tub and place the brand-new tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub as well as set in the new one. Make sure you have actually certified yourself for the job as well as are comfortable attempting it. As opposed to employing a professional to take control of a halfway-completed task, it is much better to consider using one prior to you begin. Chances are you might require a professional plumber to make tube links.
This write-up will help you mount a brand-new bathtub in your bathroom if you have actually already acquired a new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your devices as well as material list must comprise the following:
Planning for the Installation
First of all, the sustaining frame provided with the bath must be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the bathtub in the required position. The wood boards are practical in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Activate the water system as well as check all joints and also brand-new pipework for leakages and also tighten them if essential. Load the tub and likewise check the overflow outlet and also the regular electrical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's instruction manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized at least when as this will settle it right into its final position.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a rigid seal, triggering the water to pass through the wall in between the bathroom and the tiling, causing difficulties with dampness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can break relatively very early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid person who reads about How to Install a Bathtub, I figured sharing that topic was really useful. If you please set aside a second to share this blog post if you liked it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Request Estimate
Report this page